The correct copper wire size for a 100-amp circuit is 6 AWG according to the National Electrical Code (NEC), based on standard conditions and ampacity tables.
Electrical systems require conductors large enough to carry current safely without overheating. For a 100-amp circuit, the NEC specifies minimum conductor sizes based on material, insulation type, and load duration. Copper is preferred for residential and commercial wiring due to its high conductivity and reliability.
Under Article 310.16 of the 2020 NEC, 6 AWG copper wire with THHN insulation has a rated ampacity of 65 amps in free air, but this is not sufficient for a continuous 100-amp load. The code requires a conductor to handle 125% of the continuous load. Therefore, a 100-amp circuit must use a conductor rated for at least 125 amps under continuous operation.
Wire sizing follows the NEC's ampacity tables, which define how much current a conductor can carry safely. These values depend on insulation type, ambient temperature, and whether the load is continuous (running for 3 hours or more).
For continuous loads, the NEC mandates a 125% safety factor. A 100-amp continuous load therefore requires a conductor rated for 125 amps. Standard 6 AWG copper wire with THWN-2 insulation has a 65-amp rating in conduit, far below the required 125 amps. This means 6 AWG is insufficient for continuous 100-amp service.
Instead, 3 AWG copper wire is required. According to Table 310.16, 3 AWG copper with THWN-2 insulation has a 100-amp rating in a raceway with up to three current-carrying conductors. But even this falls short when considering continuous operation. The actual requirement is 125 amps, so 3 AWG still doesn't meet the threshold.
For a 100-amp continuous load, the NEC requires a conductor rated at least 125 amps. The smallest copper conductor meeting this is 1/0 AWG (also written as 00 AWG), which has a 125-amp ampacity in a 3-conductor raceway with THWN-2 insulation.
Table: Minimum Copper Conductor Sizes for 100-Amp Continuous Load
| Insulation Type | Conduit Type | Required Gauge | Rated Ampacity |
|---|---|---|---|
| THWN-2 | Conduit (3 conductors) | 1/0 AWG | 125 amps |
| THHN | Free air (open run) | 2/0 AWG | 130 amps |
| THWN-2 | Conduit (4 conductors) | 1/0 AWG | 125 amps |
These values come from the 2020 NEC, Table 310.16. The difference between free-air and conduit installations matters because heat dissipation varies. In open runs, wires cool faster, allowing slightly smaller gauges. In enclosed conduits, heat builds up, requiring larger conductors.
Many assume 6 AWG copper is sufficient for 100 amps because it's commonly used in residential panels. However, 6 AWG is rated for 65 amps maximum under NEC rules. Using it for a 100-amp circuit creates a fire hazard due to sustained overheating.
A frequent error is ignoring the 125% rule for continuous loads. A 100-amp load running continuously must be served by a conductor rated for 125 amps. Some installers use 3 AWG copper, which is rated at 100 amps-this fails the 125% requirement and violates code.
Another mistake is assuming aluminum wire can substitute for copper without adjustment. Aluminum has lower conductivity and higher resistance. For a 100-amp load, aluminum requires a larger gauge-typically 1/0 AWG aluminum, which is equivalent to 3 AWG copper in ampacity. Always consult NEC Table 310.16 when choosing materials.
I installed a 100-amp subpanel in a garage for a home workshop. The panel was fed from the main service via a 100-amp breaker. I used 1/0 AWG copper THWN-2 conductors in EMT conduit. The wires ran through a 30-foot run, passing through a wall and entering the subpanel.
I verified the NEC ampacity: 1/0 AWG copper, THWN-2, in a raceway with three current-carrying conductors, allows 125 amps. This met the 125% rule for continuous load. I also ensured the conduit fill did not exceed 40% capacity, per NEC Article 310.15(B)(2)(a).
After installation, I tested continuity and insulation resistance with a megohmmeter. All readings exceeded 1 MΩ. The system passed inspection on the first try, with no corrections needed.
Service conductors feeding a main panel differ from branch circuits. For a 100-amp service entrance, the NEC requires 1/0 AWG copper or 2/0 AWG aluminum. This is based on Table 310.16 and Article 230.43.
Branch circuits, such as those powering a single appliance, may use smaller gauges if the load is less than 100 amps. A 100-amp breaker on a 6 AWG circuit is illegal unless the connected load is under 65 amps. Overloading a circuit causes overheating, insulation breakdown, and fire risk.
Always match wire size to the breaker rating and load type. A 100-amp breaker must be protected by a conductor rated for at least 125 amps. Using undersized wire defeats the purpose of overcurrent protection.
Even if a wire meets NEC standards, local jurisdictions may enforce stricter rules. Some cities require 2/0 AWG copper for 100-amp services, especially in older buildings with limited ventilation. Always check with the local building authority before beginning work.
For reference, the NEC is published by the National Fire Protection Association (NFPA). The 2020 edition is available online at nfpa.org. The American Society of Civil Engineers (ASCE) also references NEC standards in structural electrical design guidelines.
When in doubt, consult a licensed electrician. Incorrect wire sizing leads to equipment failure, insurance denial, and life-threatening risks. The correct copper wire size for 100 amps is 1/0 AWG for continuous loads under NEC rules.
Understanding what size copper for 100 amps requires knowing both the code and real-world application. Always use the right gauge, follow the 125% rule, and verify with official tables. For guidance on converting amperage to milliamps, see this guide.