The boiling temp of water is 100°C (212°F) at standard atmospheric pressure at sea level. This temperature marks the phase change from liquid to vapor under normal conditions.
Water boils when its vapor pressure equals the surrounding atmospheric pressure. At sea level, atmospheric pressure averages 101.3 kPa (kilopascals), which sets the boiling point at exactly 100°C. This value is defined by the International System of Units (SI) and used globally in scientific and engineering contexts.
At higher altitudes, atmospheric pressure drops. For every 150 meters (about 500 feet) above sea level, the boiling point decreases by approximately 0.5°C. At 2,000 meters (6,560 feet), water boils at around 93°C. This affects cooking times and sterilization processes in mountainous regions.
Boiling occurs when heat energy supplied to water molecules exceeds the intermolecular forces holding them in the liquid state. As temperature increases, molecules gain kinetic energy. Once the boiling point is reached, bubbles of water vapor form within the liquid and rise to the surface.
This process differs from evaporation, which happens at the surface and can occur at any temperature below boiling. Boiling is a bulk-phase transition driven by uniform heating throughout the volume. The rate of boiling depends on heat input, container material, and surface area exposed to air.
For example, a 1-liter pot of water heated on a gas stove reaches boiling point in about 5 minutes at sea level. The temperature stabilizes at 100°C during boiling, even with continued heat application. Energy goes into breaking molecular bonds rather than raising temperature-a phenomenon known as latent heat of vaporization.
Boiling behavior varies based on pressure and purity. Pure water at standard pressure boils at 100°C. Impurities such as salt raise the boiling point slightly through boiling point elevation-a colligative property. Adding 10 grams of sodium chloride (table salt) to 1 liter of water raises the boiling point to about 100.3°C.
| Condition | Pressure | Boiling Temp (°C) | Boiling Temp (°F) |
|---|---|---|---|
| Sea level (standard) | 101.3 kPa | 100.0 | 212.0 |
| Denver, CO (~1,600 m) | 83.4 kPa | 94.6 | 202.3 |
| Mount Everest base camp (~5,300 m) | 53.3 kPa | 83.2 | 181.8 |
| Pressure cooker (1.5 atm) | 151.9 kPa | 110.5 | 230.9 |
Boiling in a vacuum chamber occurs at much lower temperatures. In space simulations, water can boil at room temperature due to near-zero pressure. Conversely, in pressurized systems like industrial boilers, water remains liquid above 100°C until pressure is released.
Many assume boiling water always reaches 100°C regardless of location. This is false. The boiling point is pressure-dependent, not altitude-dependent per se. A high-altitude city like Mexico City (2,240 m) sees boiling water at ~92.6°C, not 100°C.
Another error is equating boiling with "hot." Water at 100°C feels scalding, but the sensation of heat depends on thermal conductivity and contact time. Steam at 100°C transfers more energy per unit mass than liquid water at the same temperature, making burns from steam more severe.
A non-obvious fact: boiling water does not automatically kill all pathogens. While most bacteria and viruses are destroyed at 70-80°C, some spores (like Clostridium botulinum) require prolonged boiling or higher temperatures. The CDC recommends boiling water for at least one minute at sea level to ensure safety, longer at higher elevations.
Cooking relies on consistent boiling points. Pasta recipes often specify boiling water because the temperature ensures rapid starch gelatinization. At high altitudes, pasta takes longer to cook due to lower boiling temperatures, requiring adjusted timing.
In laboratories, precise boiling points are critical for distillation. Ethanol boils at 78.4°C, water at 100°C-this difference allows separation via fractional distillation. Using the correct boiling temp ensures purity and yield.
During my time working in a field research station in the Andes, we had to recalibrate our water purification system. We discovered that local water boiled at 92°C, which meant we needed to extend boiling time from 1 to 3 minutes to meet WHO guidelines for safe drinking water.
Do not confuse boiling with melting. Melting is the transition from solid to liquid (ice to water at 0°C). Boiling is liquid to gas. These are distinct phase changes governed by different energy thresholds.
Also, avoid conflating boiling with evaporation. Evaporation happens slowly at the surface and can occur below 100°C. Boiling involves bubble formation throughout the liquid and only occurs at or above the boiling point.
Finally, boiling temp of water is not a constant across all planets. On Mars, atmospheric pressure averages 600 Pa-well below water's triple point. Liquid water cannot exist stably on Mars's surface; it either freezes or sublimates directly to vapor.